| |
Emulex Fibre Channel Host Bus Adapters
| |
Major Features
- Simultaneous full duplex fibre channel 1.0625 Gb/s transfers
- Supports all fibre channel topologies
- Full fabric support using F_Port and FL_Port connections
- Full support for both FC service Class 2 and 3
- 32-bit PCI data and addressing
- Support for multiple protocols
- End-to-end parity protection
- Robust suite of software including IP and storage protocols under Windows 2000, Windows NT, NetWare, Solaris and AIX
- GLM or embedded physical interfaces
The LightPulse ™LP7000E fibre channel PCI host bus adapters
deliver exceptional performance through the use of Emulex ’s
Superfly ASIC, a 266 MIPS onboard processor and high speed
buffer memory. The LP7000E features a 32–bit PCI interface
and provides the richest set of features available.
L_Port connections, full-duplex data
transfers, high data iThe 1Gb/s LP7000E is designed to support mission-critical
enterprise applications. The LP7000E provides a unique
combination of features, including switched fabric support
using F_Port and Fntegrity features, support for all fibre
channel topologies, and support for service classes 2 and 3.
The LP7000E also features sophisticated hardware that
provides superior performance in storage area networks,
delivering low latency and high throughput in switched,
arbitrated loop and clustered environments. Support for
fiber optic cabling is provided through standard GBIC or
embedded physical interfaces.
The LightPulse™ LP7000E is complemented by a rich suite of software
support including storage protocol
(SCSI), network protocol (IP) as well
as multi-protocol (SCSI & IP)operation,
enabling advanced storage area
network (SAN) implementations in
Windows 2000,Windows NT,NetWare,
Solaris and AIX environments. All drivers
are also fully compatible with the LP9002, LP9000, LP8000, LP8000S, LP950 and LP850 (2000/NT and NetWare only) host bus adapters.
|
|
Standards
ANSI Fibre Channel FC-PH
ANSI Fibre Channel FC-AL
ANSI Fibre Channel FC-PLDA
ANSI Fibre Channel FC-FLA
FCSI 301 Rev 2.2 Gigabaud Link Module
PCI Local Bus Revision 2.2
Fibre Channel Class 2, 3
Architecture
Emulex Superfly ASIC technology
up to 33 MHz PCI bus master DMA
512 KB FLASH memory
512 KB code RAM
256 KB buffer RAM
Software Environments
Windows 2000 SCSI and IP
Windows NT 4.0 (Alpha & x86) SCSI and IP
NetWare 4.2/5.x SCSI
Solaris 2.5.1/2.6/2.7 (SPARC & x86) SCSI and IP
AIX 4.1/4.2 SCSI and IP
Hardware Environments
x86, SPARC, PowerPC and Alpha
PCI hardware platforms
Optical
| Data Rates: |
1.0625 Gb/s |
| Optics: |
short/long wave lasers |
| |
9/125 µm single-mode fiber |
| |
50/125 µm multi-mode fiber |
| |
62.5/125 µm multi-mode fiber |
| Connector Type: |
dual SC |
| |
10 K meters (32,800') 9/125 µm fiber |
| |
500 meters (1640' ) 50/125 µm fiber |
| |
175 meters (574' ) 62.5/125 µm fiber |
|
Physical Dimensions
Short PCI form factor 174.75mm x 106.68mm
(6.88" X 4.20")
Power Requirements
| Volts: |
+5 VDC |
| Power |
8 watts typical |
Environmental Conditions
| Operating Temperature: |
0° to 45° C (32° to 113° F) |
| Storage Temperature: |
-10° to 55° C (14° to 131° F) |
| Relative Humidity: |
5% to 95% non-condensing |
Agency Approvals
| Class 1 Laser Product per DHHS 21CFR (J) and EN60825 |
| UL Recognized to UL 1950 |
| CUR Recognized to CSA22.2, No. 950 |
| TUV Certified to EN60950 |
| FCC Rules, Part 15, Class B |
| ICES-003, Class B* |
| EMC Directive 89/336/EEC (CE Mark) |
| - EN55022, CISPR22/85, Class B |
| - EN50082-1 |
| Australian EMC Framework (C-Tick Mark) |
| - AS/NZS 3548, Class B |
| VCCI, Class B |
Ordering Information
| LP7000-N1 |
Multi-mode Optic Interface |
| LP7000E-N1 |
Multi-mode Optic GBIC Interface (enhanced performance) |
| LP7000E-L1 |
Single-mode Optic GBIC Interface (enhanced performance) |
|
|
|
